All posts by Site Admin

BBC B – Watford Floppy Drive

When I received delivery of the BBC B Micro I also received a single floppy drive for the computer. It is a Watford drive with a switchable 40/80 track option. The drive was dirty with a label fixed to the top of the drive.

On the bottom of the drive, one of the rubber feet was missing, so this will need to be replaced. It will be better to replace all four feet at the same time.

One problem with the drive that was initially identified was the leaver for the drive door was very loose.

Here we show the upper and lower slack that is on the drive door leaver.

I was hoping that this would be a quick fix, as I found it difficult to get  parts for 5.25″ floppy drives. After removing the screw that hold the lever on the shaft, it was very clear what the problem was, old age and years of use had taken its toll this plastic part.

As the lever was made of ABS plastic, I was hopeful that a plastic glue would help repair the leaver until I can add some pin’s into the plastic to add some strength.

Here we see the leaver repaired with the two locating plastic tags. All that next to do, is to fit a couple of metal pins to provide some additional support.

After looking inside the drive, it all looks in good order and more importantly it is all clean. A quick clean of the drive mechanics and lubrication of the moving parts was all that was needed.

The dive was re-assembled and is ready for testing.

 

BBC B Computer – Power Supply

As the BBC B is faulty and needs to be repaired, I’ve decided to start repairing the power supply. From reading some forums and the BBC B service manual it is very common for the input capacitors and some of the secondary smoothing capacitors to fail.

The power supply and capacitors here are 35 years old. Old electrolytic capacitors do fail over longer period of time.

The 2 X-Class capacitors indicated above are the input stage capacitors that tend to fail over time. Although these haven’t failed yet I am going to replace them.

These are the 2 capacitors that I have removed from the power supply. As you can see they are cracked.

…It has been a couple of weeks since this post was last updated and the replacement parts have arrived. I have decided to replace all the electrolytic capacitors on the power supply.

Here above we see all the parts that were ordered from Radionics. When you look at the YouTube video, you will hear that these new parts are smaller than their original parts.

Above we can see the parts that I am replacing in the power supply. All of these will be heading for the bin.

Before fitting the power supply back into the BBC Micro, I test the power supply. As this power supply is switch mode power supply, it requires a minimum load for the power supply to operate. In the above image you can see I am getting a supply voltage of 5.335v where it should be closer to 5v.

When the load is connected, we can see that the output voltage is 5.061v, which is much closer to the desired output voltage.

I check both the 12V and -5V outputs on the power supply and record the values of 12.07V and -4.673V for both of these outputs.

Once the testing is completed, I install the power supply back into the BBC Micro, and power it on. The dual beep at startup surprises me and indicates that all appears to be good.

I connect the BBC Micro to my desktop VGA monitor via a Composite Video to VGA adaptor and to my surprise I see the BBC Micro splash screen.

After typing *HELP and pressing ENTER, the BBC B Micro returns a list of the installed ROMS. Here I can see that DFS (Disk Filing System), Teletext Telesoft firmware and VIEW (Word processor) ROM’s are fitted.

Now that the BBC Micro is up and running, it is time to run a little BASIC program to show that it all works.

And yes, it appears that I have a working BBC B Micro.

 

BBC B Computer – First Inspection

I am excited to share that I just received a BBC B home computer, a machine that has been on my wish list for over 25 years! This one came with a floppy drive and teletext controller. I also got about 30ish 5.25″ floppy disks.

I remember first using a BBC B computer in a friend’s house back in early 1984 and yes, he did have Elite (which was loaded from a cassette tape). It was the first time I had seen a 3D wireframe game on a computer. I remember thinking how wonderful it was and wondered what the future of computer games would be like, once technology got better.

While I was in third year in secondary school, I remember when the dean of my year asked what computers the school should get for the new computer room. At that point the school only had an Apple II computer. Some students were suggesting Commodore 64’s, while a few of us suggested the Beeb. I was very happy when a few months later we got told that we were getting Beeb’s.

I remember counting the days to the delivery date and feeling very sad (Sheldon sad) when I found out that we would not have the computers until after the Christmas holidays.

When we eventually got access to the computer lab, we found out that we had a network of 16 BBC B’s for workstations, a BBC Master with double drives for the server and another BBC B with an Epson Dot Matrix printer.

Many an evening was spent after school in the computer lab, writing programs in BASIC and learning my craft. At home I was using my Dad’s Epson HX-20 portable computer and friend’s computers. Although I was repairing faulty computers for friends and family, I didn’t have enough cash to buy my own.

So for a couple of years I wrote games for the Beeb, which my classmates would play when we had computer class. I always told myself that someday I would get a BBC B. When I left school in ’87 my dad got an IBM XT Clone for work. I started my collection of computers, which never included a BBC B until now.

So, here it is, an old yellowed BBC B computer. It has that old computer smell, so I hope that all is good inside, which may not be the case considering the age of this machine, so it looks like I’ll have to RetroBright the case, top and bottom.

I can’t wait any longer. I have the screwdriver out and it is time to open the computer to have a sneak peak inside.

At first glance it all looks good inside, although pretty dusty and in need of an Econet interface upgrade. Next step is to power up the computer to see if it works. This does not give the hoped for result – I get a constant tone from the computer speaker – the most common cause of this type of problem is faulty RAM.

This is not good, so before I do any more damage, I power off the computer and order a service manual for the Beeb which was a reproduction of the original manual. Further inspection of the computer shows up a damaged tube IDC connector.

I think I have a spare 40pin IDC connecter in stock, so this is on the list of things to fix for this computer.

The date stamp on the power supply puts a manufactured date of week 22 of 1982. This makes this computer 35 years old. I do check the voltages on the power supply and verify that I measure  -5V and +5V, so it all looks good here, but I have no guarantee that it is a clean supply.

We can see from the main board that this is a revision 3 PCB.

After taking the board out and looking at the underside, I don’t see any bodge wires or hacks.

This is a good sign as it shows that no-one has tried to make any upgrades to this PCB. I hope that this means that the problems that exist are only minor issues.